Pride T 18 Car Subwoofer 2500/5000W €599.00

 599.00

Handmade 2500W RMS – 5000W Max Power Competition Pride Dual 1.65-ohm Subwoofer is known to deliver extreme output, crazy dynamics and top-notch sound quality.

In stock

+ Compare
SKU: pride-t-18-16 Category: Tags: , ,

Description

Handmade 2500W RMS – 5000W Max Power Competition Pride Dual 1.65-ohm Subwoofer is known to deliver extreme output, crazy dynamics and top-notch sound quality.

Category: Subwoofer
Weight: 32 kg (70.5 lb)
Dimensions: LWH: 535x535x360 mm (21.1×21.1×14.2 in)
Model: Pride Car Audio T18

18″ Sub Pride T18 Key Benefits

COIL

Split Design High Temperature Aluminium CCAW Voice Coil

SPIDER

Multi-layered Dual Progressive Spiders with stiched Tinsel Leads

FRAME

Die-Cast Aluminum Frame

CONE

Lightweight and stiff Real Carbon Cone and Dust Cap

MAGNETS

Massive VMS Vented Ferrite ceramic magnet system

WIRING

Heavy-Duty High Temperature Round wound Aluminum Ribbon Wire

Why T-series Subwoofer?

  1. Reduced Basket Resonation

  2. Cut down back wave interference

  3. Dual Flat Progressive Spiders

  4. Enhanced Thermal Capacity and Mech Strength

  5. Impressive Power Handling

Pride 18″ T-series Subwoofer Features

COIL

A longer copper coil and more room for suspension travel provide reduced distortion at higher output levels.

SPIDER

Venting in the back-bracing of the cone and perimeter of the spider landing provides maximum air-flow to cool the voice-coil during operation.

FRAME

Built with rugged cast Aluminium frame for dimensional stability and to eliminate stray magnetic fields for improved magnetic focus.

CONE

Woven fiber pressed paper cone helps reproduce tight and accurate bass with minimal cone distortion.

MAGNETS

DMA optimized motor system reduces distortion.

WIRING

Speaker leads are stitched and glued to the spider rolls for reliable performance when pushed to the limits.

SURROUND

Tough Santoprene surround with interlocking front gasket.

POLE

Flared rear vented pole piece for lower back pressure and better air flow to improve power handling and lower vent noise.

Pride Subwoofer is an attractive buy, very well built for its price.

To enhance the reliability and performance by reducing fatigue and possible shorting, in the Pride T-series Subwoofer, Pride engineers have stitched the tinsel leads to the spider. The multipoint periodic stitching lead wires reduce the mass of the tinsel leads to spread the stress over a greater area.

To increase the surface area of the cone (Sd), which is actually , Pride Subwoofer features a new way for the surround to adhere to the basket, gaining up to 25% more effective radiating cone area, and seriously improving the nominal efficiency and maximum output.

  • A longer copper coil and more room for suspension travel provide reduced distortion at higher output levels.

  • Venting in the back-bracing of the cone and perimeter of the spider landing provides maximum air-flow to cool the voice-coil during operation.

  • Built with rugged cast Aluminium frame for dimensional stability and to eliminate stray magnetic fields for improved magnetic focus.

  • Woven fiber pressed paper cone helps reproduce tight and accurate bass with minimal cone distortion.

  • Speaker leads are stitched and glued to the spider rolls for reliable performance when pushed to the limits.

  • DMA optimized motor system reduces distortion.

  • Tough Santoprene surround with interlocking front gasket.

  • Model: T
  • Woofer size: 18-inch
  • Voice coil diameter: 76 mm 3-inch
  • Sensitivity (2.83V 1m): 94.2 dB
  • Impedance: Dual 1.65-ohm
  • Peak power (Max): 5000W
  • Power (RMS): 2500W
  • Free air resonance (Fs): 27 Hz
  • Excursion (Xmax) one-way BL 50%: 33 mm
  • Voice coil DC resistance (Re): 3.3 ohms
  • Total speaker Q value (Qts): 0.34
  • Equivalent compliance (Vas): 120 L (4057.7 oz)
  • Efficiency (SPL 1W 1m): 90.4 dB
  • Cone area (Sd): 1165 sq cm (180.6 cu in)
  • Force Factor (BL): 29.5
  • Voice coil material: High Temperature Copper
  • Suggested sealed: 0.1 m3 (3.53 cu ft)
  • Suggested ported: 0.15 m3 (5.29 cu ft) port 432.3 cm2 (67 sq in) length 50.8 cm (20 in)
  • Frame material: Heavy duty die cast aluminum

Shop with confidence and take advantage of

Full manufacturer’s warranty for one year

  1. 30-Day money-back guarantee

  2. Premium hand-made build quality

  3. No questions asked easy returns

  4. Customer service by phone/email

Pride T18D16 is hand-built weather-proof and tough as nails

Operating conditions
Humidity up to 90% (normal/salt-fog)
Storage temperature -20°C to 50°C (-4°F to 122°F)
Working temperature 5°C to 40°C ( 4°F to 104°F)

Additional information

Weight 32 kg
Dimensions 53.5 × 53.5 × 36 cm
Model

Woofer size

Voice coil diameter

76mm 3"

Voice coil material

High Temperature Copper

Sensitivity (2.83V/1m)

94.2 dB

Impedance

Dual 1.65-ohm

Peak power (Max)

5000W

Power (RMS)

2500W

Suggested sealed

0.1 m3 (3.53 cu ft)

Suggested ported

0.15 m3 (5.29 cu ft) port 432.3 cm2 (67 sq in) length 50.8 cm (20 in)

Free air resonance (Fs)

27 Hz

Excursion (Xmax) one-way BL 50%

33 mm

Voice coil DC resistance (Re)

3.3 ohms

Total speaker Q value (Qts)

0.34

Equivalent compliance (Vas)

120 L (4057.7 oz)

Efficiency (SPL 1W/1m)

90.4 dB

Cone area (Sd)

1165 cm² (180.6 sq in)

Force Factor (BL)

29.5

Shipping label

HP

Brand

Pride Car Audio

Google product category

2833

Leave a Review

Rating
Please select a star rating
Please write a review

Connect with

Facebook Twitter